Polaris Pro XP Vehicle Lift Guide
Safely lift your Polaris Pro XP or RZR XP using the AGM Manual Jack PRO. Tested on a real vehicle during real trail repairs.
Estimated Read Time: 1–2 Minutes
Quick Answers
★★★★★ Preferred Rear Lift: Rear trailing arm
★★★★★ Preferred Front Lift: Front side chassis tube
★★★★☆ Alternate Rear: Lower radius rod
★★★★☆ Alternate Rear: Rear side chassis tube (Combo Hook)
★★★★☆ Alternate Front: Front side chassis tube (Combo Hook)
Avoid: Unsupported plastic, unstable ground, lifting with the vehicle able to roll.
You're in the Right Place If...
-
You have a flat tire on a Polaris Pro XP.
-
You want the safest lift points.
-
You're using an AGM Manual Jack PRO.
-
You want to avoid damaging your vehicle.
-
You want to get back on the trail quickly.
Flat Tire Repair
-
If using hand tools, loosen lug nuts before lifting.
-
Lift from the preferred lift point.
-
Place a cooler, toolbox, spare tire, or similar solid object under the vehicle as a secondary support.
-
Remove the lug nuts, catching each one if possible.
-
If a lug nut falls into dirt or sand, clean it before reinstalling so the threads are not damaged.
-
Install the replacement wheel.
-
Start every lug nut by hand.
-
Tighten in a star pattern.
-
Torque to Polaris specifications whenever possible. If a torque wrench is not available, tighten with an impact to get you home.
Preferred Rear Lift
Lift Here
Rear trailing arm beneath the shock.
Why
-
Fastest rear lift.
-
Minimizes suspension travel.
-
Two points of contact create a very stable lift.
-
Jack body braces against the suspension spring for added stability.
Watch Out
-
Position the pad directly beneath the trailing arm.
-
Push the jack firmly against the spring before lifting.
Trail Tip
Two points of contact help stabilize the jack and reduce movement during the lift.
Alternate Rear Lift
📷 Photo
Lift Here
Lower radius rod just before the bend.
Why
-
Excellent backup when the trailing arm is blocked.
Watch Out
-
Vehicle must be in Park.
-
Chock a tire whenever possible before lifting.
-
Lift only from the straight section of the radius rod.
Trail Tip
Inline lifts allow the jack to roll with the vehicle, so always prevent vehicle movement first.
📷 Photo
Lift Here
Rear side chassis tube using the AGM Combo Hook.
Why
-
Secure engagement inside the chassis tube.
-
Great option when suspension access is limited.
Watch Out
-
Make sure the Combo Hook pin is fully seated before lifting.
Trail Tip
The Combo Hook creates an additional lift point without contacting suspension components.
Preferred Front Lift
📷 Photo
Lift Here
Front side chassis tube.
Why
-
Stable lift geometry.
-
Jack stands upright as the vehicle rises.
-
Repeatable lift location.
Watch Out
-
Start with the base of the jack slightly farther under the vehicle than the top so the jack stands vertical as the suspension unloads.
Trail Tip
Confirm the jack pad is fully under the chassis tube before applying load.
Alternate Front Lift
📷 Photo
Lift Here
Front side chassis tube using the AGM Combo Hook.
Why
-
Provides another secure lifting option.
-
Positive engagement into the chassis opening.
Watch Out
-
Verify the Combo Hook is fully engaged before lifting.
Trail Tip
The Combo Hook pin registers into the chassis opening, helping prevent the jack from shifting.
Common Mistakes
-
Lifting on unsupported plastic.
-
Forgetting to chock a tire during inline lifts.
-
Starting lug nuts with an impact.
-
Tightening lug nuts in a circle.
-
Crawling under a vehicle supported only by a jack.
Trail Safety Checklist
✓ Move off the trail whenever possible.
✓ Park on level ground.
✓ Vehicle in Park.
✓ Four-wheel drive engaged.
✓ Chock a tire if needed.
✓ Use a secondary support before putting any part of your body underneath the vehicle.
Questions We Hear Most
Why is the trailing arm the preferred rear lift?
It minimizes suspension travel, lifts the tire quickly, and allows the jack to stabilize against the spring.
When should I use the Combo Hook?
Whenever you need to lift from the chassis tube instead of the suspension.
Why should I start the jack leaning slightly inward?
As the vehicle pivots during the lift, the jack stands upright, creating a more stable lifting position.
Should I loosen the lug nuts before lifting?
Yes, if you're using hand tools. An impact makes this less important.
Continue Learning
▶ Watch the Polaris Pro XP Lift Video
Scissor Jack Vehicle Lift Guide
Manual Jack Sport Vehicle Lift Guide
Electric Jack PRO Vehicle Lift Guide
Choosing the Right AGM Trail Jack – Coming Soon
